✅Auto VIN, 4 In 1 Live Data

✅Print Real-time Diagnostic Report

✅Read/Clear code Error

✅Support 28 Languages: English, German, Spanish, French, Italian, Portuguese, Russian, Polish, Turkish, Dutch, Hungarian, Chinese (Traditional), Greek, Slovak, Romanian, Arabic, Croatian, Slovene, Finnish, Japanese, Korean, Czech, Persian, Swedish, Serbian, Danish, Vietnamese , Bulgarian

Protocols: SAE J1850 PWM, SAE J1850 VPW, ISO 9141-2 ISO, ISO 14230-4 KWP, ISO 15765-4, CAN, CANFD

1.Adblue Reset(Diesel Engine Exhaust Gas Filter)

After the diesel exhaust treatment fluid (car adblue) is replaced or filled up, Turn off the adblue fault indicator light by adblue reset.

2.EGR Self-Learning

If the EGR fails, the engine/EPC fault indicator light of the vehicle instrument will light up, and the EGR self-learning function can turn off the fault indicator light after cleaning or replacing the EGR valve.

3.A/F Reset

This function is applied to set or learn Air/Fuel ratio parameters.

4.ABS Bleeding

In the case of replacement of ABS system, ABS pump, brake pump, brake line and brake fluid, it is necessary to bleeding the ABS system through the ABS bleeding function.

5.BMS battery reset

For a vehicle with the battery management function, if the battery status is detected as faulty (aging or damaged), the fault code will saved in the ECU. After replacing the battery and running "BMS Reset", it can delete the fault code and re-match, based on the relevant information of the existing battery as the standard, let the monitoring unit monitor. Avoid false positives from instrument error messages

6.Gear Learning

Gear learning is required when replacing the engine ECU, crankshaft position sensor, crankshaft flywheel, and fault code that the gear has not learned,it is necessary to gear learning.

7.Brake Reset

1. When the brake is used to a certain thickness, the brake sensor line will be worn, and the brake pad sensor line will send a signal to the car computer to prompt the replacement of the brake pad. After replacing the brake pads, the brake needs to be reset, otherwise the car will still alarm.

2. Need to do the reset situation:

a. replace the brake pad and brake pad wear induction line;

b. brake pad indicator light on;

c. brake pad sensor line short-circuit repair;

d. After replacing the servomotor

8..DPF(Diesel Particulate Filter) Regeneration

Diesel Particulate Filter in the working process, particles will accumulate in the filter, when it reaches a certain value, it will lead to engine power and economic performance decline, must be removed in time to ensure that DPF continues to work normally.

9.ETS Learning(throttle matching)

Need to perform throttle matching: Replace the electronic control unit, power off the electronic control unit, replace the electronic throttle assembly, replace or disassemble the intake port, clean the throttle.

10.Gearbox (Transmission )Reset

When the transmission parts wear and aging become serious, the adaptive learning of the control unit does not work, and the parts need to be repaired and replaced, then the automatic transmission control unit needs to be forced to learn.

11.Injector Coding

After replacing the ECU or injector, each cylinder injector needs to be coded to confirm or recode. So that the cylinder can better identify each cylinder injector, accurate control of fuel injection.

12.Nox Sensor Reset

Nox sensor is a sensor used to detect the content of nitrogen oxides (Nox) in engine exhaust. lf the Nox fault is re-initialized and the Nox catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU.

13.Oil Reset

If the oil maintenance light is on, the car needs to be maintained. After the maintenance, the driving time and other data should be reset to zero, so that the maintenance light will be turned off, and the car system will enable a new maintenance cycle.

14.SAS Steering Angel Reset

After the vehicle is disassembled or replaced with parts related to the steering function, the steering Angle learning function needs to be performed.

15.TPMS Tire Pressure Reset

only applicable to vehicles without a tire pressure sensors.

if the tire pressure is too low or air leaking, replacing or installing tire pressure monitoring equipment, replacing tires, tire pressure sensor damage, and cars with tire pressure monitoring function in the case of tire transposition etc,.Tire pressure reset is required after vehicle maintenance and turn off the tire pressure fault indicator light.

Support 10 FULL OBDII Test Modes

This obd2 scanner can support all 10 OBD2 test modes. Read Codes, Erase Codes, MIL Fault Indicator Light, Live Data, EVAP System Test, On-Board Monitor Test, View Freeze Frame, O2 Sensor Test, Vehicle Info, I/M Readiness, DTC Code Look-up, perform oxygen sensor tests and carbon canister tests to ensure your vehicle is ready for all emission services.

Car scan tool support agreement: ISO 14230-4(KWP2000)/ IOS 15765-4(CAN)/ ISO 9141-2(IOS)/ ISO14229(UDS)/ SAEJ 1850(VPW&PWM)

The ultimate diagnostic tool supports a wide range of crucial protocols, including CANFD—now supporting for SGM, for GM, for CHRYSLER.

[2021][Chevrolet][Onix]
CANFD6&14,[Chevrolet][Tracker] CANFD6&14,[Chevrolet][Suburban]
CCMA,[Cadillac][Escalade ESV] CCMA,[Cadillac][Escalade] CCMA,[GMC][YUKON XL]
CCMA,[GMC][YUKON] CCMA,[Chevrolet][Onix] ALL SYSTEM,[Chevrolet][Tracker] ALL
SYSTEM,[Chevrolet][Suburban] CCMA,[Cadillac][Escalade ESV]
CCMA,[Cadillac][Escalade] CCMA,[GMC][YUKON XL] CCMA,[GMC][YUKON] CCMA

[2023][Chevrolet][Montana] ALL
SYSTEM,[Chevrolet][Montana] CANFD6&14

[2024][Buick][Electra E5]
VSIM,[GMC][Sierra] H/U TCM 10 Speed (MGM)/10 Speed (MGU),[Buick][Electra E5]VSIM,[GMC][Sierra] H/U TCM 10 Speed , (MGM)/10 Speed (MGU)